Beryllium valve seat

A place to talk about things that do not fit into any other forum, only members may post to keep out the SPAM
Post Reply
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Beryllium valve seat

Post by Hotz »

Hello guys ...
some information interference assembly seat valves.
I have to head Alfa 164-V6 repair, seat Beryllium ...
In normal use seats of valves **steel** 0.10 / 0.12 mm (0.00394/0.00464 ¨) Pressure to install
Anyone with information?

Image
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
Top
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: Beryllium valve seat

Post by Hotz »

Something here...


>>> http://www.speedfreak.pt/Catalogo/CV4CatalogONLINE.pdf <<<
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
Top
SWAirflowServices
Posts: 143
Joined: Tue Jun 15, 2010 7:51 pm
Location: So Cal
Contact:
Contact SWAirflowServices

Re: Beryllium valve seat

Post by SWAirflowServices »

$169 per valve for a motorcycle application? $676 a set? No wonder I haven't used these before.
http://www.facebook.com/SWAirFlowServices You know you want to "Like" it!
Top
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: Beryllium valve seat

Post by Hotz »

SWAirflowServices...

Hard work or not?

Image
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
Top
SWAirflowServices
Posts: 143
Joined: Tue Jun 15, 2010 7:51 pm
Location: So Cal
Contact:
Contact SWAirflowServices

Re: Beryllium valve seat

Post by SWAirflowServices »

No, not bad at all. Likes a squirt of lube when you are machining the valve seat profile. Also, we end up doing some weird oscillations with the cutter speed. It's like the material likes a load on the cutter so we start with a slow speed and give it a "stab of the throttle" when it starts cutting.

Oh, and be careful because Beryllium is a very carcinogenic substance! :roll:

Shane
http://www.facebook.com/SWAirFlowServices You know you want to "Like" it!
Top
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: Beryllium valve seat

Post by Hotz »

thanks shane ...

Valuable information ...

good luck...
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
Top
Tony
Posts: 1445
Joined: Wed Mar 03, 2010 3:40 pm
Location: Melbourne, Australia

Re: Beryllium valve seat

Post by Tony »

Shane is right, beryllium is also used a lot in the electronics industry for it's hardness and very high thermal conductivity.

It is also EXTREMELY poisonous, especially any dust from cutting, fracture, or grinding.
Keep it right out of your lungs or any open wounds, it is very nasty stuff.
Also known as the infamous "Warpspeed" on some other Forums.
Top
Dan_DiM
Posts: 27
Joined: Sat Mar 03, 2012 9:45 pm

Re: Beryllium valve seat

Post by Dan_DiM »

i never cut it on valve seats but used to make bushings out if it. use sharp cutters because it work hardens easily.
Top
Hotz
Posts: 709
Joined: Thu Feb 25, 2010 10:37 pm

Re: Beryllium valve seat

Post by Hotz »

This is scary.. :o

Work and self-care :idea:

http://www.lookfordiagnosis.com/cases.p ... sis&lang=1
Sorry my english mistakes.
PTS Parts>> http://www.flowbenchtech.com/store.html
Top
86rocco
Posts: 292
Joined: Thu Mar 04, 2010 9:01 pm

Re: Beryllium valve seat

Post by 86rocco »

Scary stuff indeed!

Those cases dealt with long term exposure, any idea what the risks associated with short term occasional exposure are?
Top
Post Reply

Return to “General BS”