I have perfornance trends Port Flow Analyzer software and I am trying to set it up, can any one tell how I go about working out my benches flow ranges so I can put them in to the software.
Rick
Performance trends software need help
12 posts
• Page 1 of 1
by larrycavan » Sun Nov 06, 2005 7:06 pm
Do you mean working out what your bench actually flows or the steps to setup custom orifice sized in the software?
- larrycavan
- Site Admin
- Posts: 1183
- Joined: Fri Apr 01, 2005 4:40 pm
by larrycavan » Sun Nov 06, 2005 9:40 pm
Have you calibrated your ranges?
Do you have the PT electronics?
Do you have the PT electronics?
- larrycavan
- Site Admin
- Posts: 1183
- Joined: Fri Apr 01, 2005 4:40 pm
by rbracer » Sun Nov 06, 2005 10:23 pm
No electronics at this time, only the software.
The calibrating is what I am trying to work out, I have the ranges which are writen on the bench and I have a Calibration plate with a hole in it to check the machine and get any correction facter I need.
Rick
The calibrating is what I am trying to work out, I have the ranges which are writen on the bench and I have a Calibration plate with a hole in it to check the machine and get any correction facter I need.
Rick
- rbracer
- Posts: 11
- Joined: Tue Mar 02, 2004 5:26 pm
by Thomas Vaught » Sun Nov 06, 2005 10:49 pm
If you provide the orifice sizes to the forum, we can use a spreadsheet like Rocco86 excel program to get you close on the ranges. You can then use your calibration plate to fine tune the deal.
Tom V.
Tom V.
- Thomas Vaught
- Posts: 465
- Joined: Fri Feb 18, 2005 5:36 pm
- Location: Michigan
by larrycavan » Mon Nov 07, 2005 12:42 am
- larrycavan
- Site Admin
- Posts: 1183
- Joined: Fri Apr 01, 2005 4:40 pm
by larrycavan » Mon Nov 07, 2005 12:58 pm
That should do it.
What kind of bench do you have?
If you haven't done it yet, I would grab Rocco's spreadsheet on orifice calculations. It's quite accurate and easy to use.
Larry C.
What kind of bench do you have?
If you haven't done it yet, I would grab Rocco's spreadsheet on orifice calculations. It's quite accurate and easy to use.
Larry C.
- larrycavan
- Site Admin
- Posts: 1183
- Joined: Fri Apr 01, 2005 4:40 pm
by rbracer » Mon Nov 07, 2005 5:09 pm
Larry C
Thanks for the help, I will try putting that in to the software to day.
The bench I have is a FMA it is built here in Australia, I am hopping to also fit the Performance Trend electronics as soon as I can.
Rick
Thanks for the help, I will try putting that in to the software to day.
The bench I have is a FMA it is built here in Australia, I am hopping to also fit the Performance Trend electronics as soon as I can.
Rick
- rbracer
- Posts: 11
- Joined: Tue Mar 02, 2004 5:26 pm
by rbracer » Mon Nov 07, 2005 5:12 pm
Larry C
Thanks for the help, I will try putting that in to the software to day.
The bench I have is a FMA it is built here in Australia, I am hopping to also fit the Performance Trend electronics as soon as I can, I found some spreadsheets stuf on this site yesterday and down loaded them I think that one was there.
Rick
Thanks for the help, I will try putting that in to the software to day.
The bench I have is a FMA it is built here in Australia, I am hopping to also fit the Performance Trend electronics as soon as I can, I found some spreadsheets stuf on this site yesterday and down loaded them I think that one was there.
Rick
- rbracer
- Posts: 11
- Joined: Tue Mar 02, 2004 5:26 pm
by larrycavan » Mon Nov 07, 2005 10:44 pm
Rick,
If your bench is like the SF110 design, don't forget to use the temperature correction factors.
Hope the PT stuff works out well. Guys that report having them seem to relly like them...
Larry C
If your bench is like the SF110 design, don't forget to use the temperature correction factors.
Hope the PT stuff works out well. Guys that report having them seem to relly like them...
Larry C
- larrycavan
- Site Admin
- Posts: 1183
- Joined: Fri Apr 01, 2005 4:40 pm
12 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 29 guests